在Centos 5.6下安装 dynamips
作者 佚名技术
来源 Linux系统
浏览
发布时间 2012-04-03
| sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) 3600 Software (C3640-I-M), Version 12.2(13)T1, RELEASE SOFTWARE (fc1) TAC Support: [url]http://www.cisco.com/tac[/url] Copyright (c) 1986-2003 by cisco Systems, Inc. Compiled Fri 03-Jan-03 15:10 by ccai Image text-base: 0x60008930, data-base: 0x60C1A000 cisco 3640 (R4700) processor (revision 0xFF) with 126976K/4096K bytes of memory. Processor board ID 00000000 R4700 CPU at 100Mhz, Implementation 33, Rev 1.2 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 4 Serial network interface(s) DRAM configuration is 64 bits wide with parity enabled. 125K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: y At any point you may enter a question mark ''?'' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets ''[]''. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: n First, would you like to see the current interface summary? [yes]: y Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address OK? Method Status Prot ocol FastEthernet0/0 unassigned NO unset up up Serial1/0 unassigned NO unset up down Serial1/1 unassigned NO unset up down Serial1/2 unassigned NO unset up down Serial1/3 unassigned NO unset up down Configuring global parameters: Configuring global parameters: Enter host name [Router]: croutera3640 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter enable secret: aaa The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter enable password: aaa1 The virtual terminal password is used to protect access to the router over a network interface. Enter virtual terminal password: aaa2 Configure SNMP Network Management? [yes]: n Configure IP? [yes]: y Configure IGRP routing? [yes]: n Configure RIP routing? [no]: n Configure bridging? [no]: n Async lines accept incoming modems calls. If you will have users dialing in via modems, configure these lines. Configure Async lines? [yes]: n Configuring interface parameters: Do you want to configure FastEthernet |
凌众科技专业提供服务器租用、服务器托管、企业邮局、虚拟主机等服务，公司网站：http://www.lingzhong.cn 为了给广大客户了解更多的技术信息，本技术文章收集来源于网络,凌众科技尊重文章作者的版权，如果有涉及你的版权有必要删除你的文章，请和我们联系。以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息，谢谢! |
你可能对下面的文章感兴趣
上一篇: 如何架设Linux打印服务器下一篇: linux系统账号和密码策略
关于在Centos 5.6下安装 dynamips的所有评论
